USB: gadgetfs: copy_to_iter() returns the number of bytes copied.

Documentation/arm/Atmel/README

@@ -90,6 +90,11 @@ the Atmel website: http://www.atmel.com.
         + Datasheet
           http://www.atmel.com/Images/Atmel-11238-32-bit-Cortex-A5-Microcontroller-SAMA5D4_Datasheet.pdf
 
+      - sama5d2 family
+        - sama5d27
+        + Datasheet
+          Coming soon
+
 
 Linux kernel information
 ------------------------

Documentation/devicetree/bindings/arm/atmel-at91.txt

@@ -27,6 +27,8 @@ compatible: must be one of:
     o "atmel,at91sam9xe"
  * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific
    SoC family:
+    o "atmel,sama5d2" shall be extended with the specific SoC compatible:
+       - "atmel,sama5d27"
     o "atmel,sama5d3" shall be extended with the specific SoC compatible:
        - "atmel,sama5d31"
        - "atmel,sama5d33"
@@ -39,6 +41,10 @@ compatible: must be one of:
        - "atmel,sama5d43"
        - "atmel,sama5d44"
 
+Chipid required properties:
+- compatible: Should be "atmel,sama5d2-chipid"
+- reg : Should contain registers location and length
+
 PIT Timer required properties:
 - compatible: Should be "atmel,at91sam9260-pit"
 - reg: Should contain registers location and length
@@ -50,6 +56,7 @@ System Timer (ST) required properties:
 - reg: Should contain registers location and length
 - interrupts: Should contain interrupt for the ST which is the IRQ line
   shared across all System Controller members.
+- clocks: phandle to input clock.
 Its subnodes can be:
 - watchdog: compatible should be "atmel,at91rm9200-wdt"
 
@@ -61,7 +68,7 @@ TC/TCLIB Timer required properties:
   Note that you can specify several interrupt cells if the TC
   block has one interrupt per channel.
 - clock-names: tuple listing input clock names.
-	Required elements: "t0_clk"
+	Required elements: "t0_clk", "slow_clk"
 	Optional elements: "t1_clk", "t2_clk"
 - clocks: phandles to input clocks.
 
@@ -87,18 +94,20 @@ One interrupt per TC channel in a TC block:
 
 RSTC Reset Controller required properties:
 - compatible: Should be "atmel,<chip>-rstc".
-  <chip> can be "at91sam9260" or "at91sam9g45"
+  <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3"
 - reg: Should contain registers location and length
+- clocks: phandle to input clock.
 
 Example:
 
 	rstc@fffffd00 {
 		compatible = "atmel,at91sam9260-rstc";
 		reg = <0xfffffd00 0x10>;
+		clocks = <&clk32k>;
 	};
 
 RAMC SDRAM/DDR Controller required properties:
-- compatible: Should be "atmel,at91rm9200-sdramc",
+- compatible: Should be "atmel,at91rm9200-sdramc", "syscon"
 			"atmel,at91sam9260-sdramc",
 			"atmel,at91sam9g45-ddramc",
 			"atmel,sama5d3-ddramc",
@@ -117,6 +126,7 @@ required properties:
 - compatible: Should be "atmel,<chip>-shdwc".
   <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5".
 - reg: Should contain registers location and length
+- clocks: phandle to input clock.
 
 optional properties:
 - atmel,wakeup-mode: String, operation mode of the wakeup mode.
@@ -135,9 +145,10 @@ optional at91sam9x5 properties:
 
 Example:
 
-	rstc@fffffd00 {
-		compatible = "atmel,at91sam9260-rstc";
-		reg = <0xfffffd00 0x10>;
+	shdwc@fffffd10 {
+		compatible = "atmel,at91sam9260-shdwc";
+		reg = <0xfffffd10 0x10>;
+		clocks = <&clk32k>;
 	};
 
 Special Function Registers (SFR)
@@ -155,3 +166,55 @@ required properties:
 		compatible = "atmel,sama5d3-sfr", "syscon";
 		reg = <0xf0038000 0x60>;
 	};
+
+SHDWC Shutdown Controller (Alternative)
+
+1) shdwc node
+
+required properties:
+- compatible: should be "atmel,sama5d2-shdwc".
+- reg: should contain registers location and length
+- #address-cells: should be one. The cell is the wake-up input index.
+- #size-cells: should be zero.
+
+optional properties:
+
+- atmel,wakeup-debouncer: minimum wake-up inputs debouncer period in
+  micro-seconds. It's usually a board-related property.
+- atmel,wakeup-rtc-timer: boolean to enable Real-Time Clock wake-up.
+
+The node contains child nodes for each wake-up input that the platform uses.
+
+2) input nodes
+
+Wake-up input nodes are usually described in the "board" part of the Device
+Tree. Note also that input 0 is linked to the wake-up pin and is frequently
+used.
+
+Required properties:
+- reg: should contain the wake-up input index [0 - 15].
+
+Optional properties:
+- atmel,wakeup-type: string, operation mode of the input described by the child
+  node. Supported values are: "high" or "low".
+
+Example:
+
+On the SoC side:
+	shdwc@f8048010 {
+		compatible = "atmel,sama5d2-shdwc";
+		reg = <0xf8048010 0x10>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		atmel,wakeup-rtc-timer;
+	};
+
+On the board side:
+	shdwc@f8048010 {
+		atmel,shdwc-debouncer = <976>;
+
+		input@0 {
+			reg = <0>;
+			atmel,wakeup-type = "low";
+		};
+	};

Documentation/devicetree/bindings/clock/at91-clock.txt

@@ -77,6 +77,9 @@ Required properties:
 	"atmel,sama5d4-clk-h32mx":
 		at91 h32mx clock
 
+	"atmel,sama5d2-clk-generated":
+		at91 generated clock
+
 Required properties for SCKC node:
 - reg : defines the IO memory reserved for the SCKC.
 - #size-cells : shall be 0 (reg is used to encode clk id).
@@ -461,3 +464,35 @@ For example:
 		compatible = "atmel,sama5d4-clk-h32mx";
 		clocks = <&mck>;
 	};
+
+Required properties for generated clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the generated clock source phandles.
+	e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
+- name: device tree node describing a specific generated clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: peripheral id. See Atmel's datasheets to get a full
+	  list of peripheral ids.
+	* atmel,clk-output-range : minimum and maximum clock frequency
+	  (two u32 fields).
+
+For example:
+	gck {
+		compatible = "atmel,sama5d2-clk-generated";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
+
+		tcb0_gclk: tcb0_gclk {
+			#clock-cells = <0>;
+			reg = <35>;
+			atmel,clk-output-range = <0 83000000>;
+		};
+
+		pwm_gclk: pwm_gclk {
+			#clock-cells = <0>;
+			reg = <38>;
+			atmel,clk-output-range = <0 83000000>;
+		};
+	};

Documentation/devicetree/bindings/i2c/i2c-at91.txt

@@ -2,8 +2,8 @@ I2C for Atmel platforms
 
 Required properties :
 - compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c",
-     "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c"
-     or "atmel,at91sam9x5-i2c"
+     "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c",
+     "atmel,at91sam9x5-i2c" or "atmel,sama5d2-i2c"
 - reg: physical base address of the controller and length of memory mapped
      region.
 - interrupts: interrupt number to the cpu.
@@ -13,6 +13,12 @@ Required properties :
 
 Optional properties:
 - clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
+- dmas: A list of two dma specifiers, one for each entry in dma-names.
+- dma-names: should contain "tx" and "rx".
+- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
+  capable I2C controllers.
+- atmel,twd-hold-cycles: specify hold cycles to increase the TWD hold time,
+   the maximum value is 0x1f.
 - Child nodes conforming to i2c bus binding
 
 Examples :
@@ -25,10 +31,33 @@ i2c0: i2c@fff84000 {
 	#size-cells = <0>;
 	clocks = <&twi0_clk>;
 	clock-frequency = <400000>;
+	atmel,twd-hold-cycles = <2>;
 
 	24c512@50 {
 		compatible = "24c512";
 		reg = <0x50>;
 		pagesize = <128>;
 	}
 }
+
+i2c0: i2c@f8034600 {
+	compatible = "atmel,sama5d2-i2c";
+	reg = <0xf8034600 0x100>;
+	interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+	dmas = <&dma0
+		(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+		AT91_XDMAC_DT_PERID(11)>,
+	       <&dma0
+		(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+		AT91_XDMAC_DT_PERID(12)>;
+	dma-names = "tx", "rx";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&flx0>;
+	atmel,fifo-size = <16>;
+
+	wm8731: wm8731@1a {
+		compatible = "wm8731";
+		reg = <0x1a>;
+	};
+};

Documentation/devicetree/bindings/iio/adc/at91-sama5d2_adc.txt

@@ -0,0 +1,27 @@
+* AT91 SAMA5D2 Analog to Digital Converter (ADC)
+
+Required properties:
+  - compatible: Should be "atmel,sama5d2-adc".
+  - reg: Should contain ADC registers location and length.
+  - interrupts: Should contain the IRQ line for the ADC.
+  - clocks: phandles to clocks.
+  - clock-names: tuple listing clock names.
+      Required elements: "adc_clk", "adc_op_clk". "adc_clk" is the peripheral
+      clock, "adc_clk" is the sampling clock.
+  - vref-supply: Supply used as reference for conversions.
+
+Optional properties:
+  - vddana-supply: Supply for the adc device.
+
+
+Example:
+
+adc: adc@fc030000 {
+	compatible = "atmel,sama5d2-adc";
+	reg = <0xfc030000 0x100>;
+	interrupts = <40 IRQ_TYPE_LEVEL_HIGH 7>;
+	clocks = <&adc_clk>, <&adc_op_clk>;
+	clock-names = "adc_clk", "adc_op_clk";
+	vddana-supply = <&vdd_3v3_lp_reg>;
+	vref-supply = <&vdd_3v3_lp_reg>;
+}

Documentation/devicetree/bindings/interrupt-controller/atmel,aic.txt

@@ -2,7 +2,7 @@
 
 Required properties:
 - compatible: Should be "atmel,<chip>-aic"
-  <chip> can be "at91rm9200", "sama5d3" or "sama5d4"
+  <chip> can be "at91rm9200", "sama5d2", "sama5d3" or "sama5d4"
 - interrupt-controller: Identifies the node as an interrupt controller.
 - interrupt-parent: For single AIC system, it is an empty property.
 - #interrupt-cells: The number of cells to define the interrupts. It should be 3.

Documentation/devicetree/bindings/media/atmel-isi.txt

@@ -2,7 +2,7 @@ Atmel Image Sensor Interface (ISI) SoC Camera Subsystem
 ----------------------------------------------
 
 Required properties:
-- compatible: must be "atmel,at91sam9g45-isi"
+- compatible: should be "atmel,at91sam9g45-isi" or "atmel,sama5d2-isc";
 - reg: physical base address and length of the registers set for the device;
 - interrupts: should contain IRQ line for the ISI;
 - clocks: list of clock specifiers, corresponding to entries in

Documentation/devicetree/bindings/mfd/atmel-flexcom.txt

@@ -0,0 +1,67 @@
+* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
+
+The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
+controller and an USART. Only one function can be used at a time and is chosen
+at boot time according to the device tree.
+
+Required properties:
+- compatible:		Should be "atmel,sama5d2-flexcom"
+- reg:			Should be the offset/length value for Flexcom dedicated
+			I/O registers (without USART, TWI or SPI registers).
+- clocks:		Should be the Flexcom peripheral clock from PMC.
+- #address-cells:	Should be <1>
+- #size-cells:		Should be <1>
+- ranges:		Should be one range for the full I/O register region
+			(including USART, TWI and SPI registers).
+- atmel,flexcom-mode:	Should be one of the 3 following macros as defined in
+			include/dt-bindings/mfd/atmel-flexcom.h:
+			- ATMEL_FLEXCOM_MODE_USART for USART
+			- ATMEL_FLEXCOM_MODE_SPI for SPI
+			- ATMEL_FLEXCOM_MODE_TWI for I2C
+
+Required child:
+a single child device of type matching the "atmel,flexcom-mode" property.
+
+The reg property of this child should be:
+- <0x200 0x200> for USART
+- <0x400 0x200> for SPI
+- <0x600 0x200> for I2C
+
+The phandle provided by the clocks property of the child is the same as one for
+the Flexcom parent.
+
+Other properties remain unchanged. See documentation of the respective device:
+- ../serial/atmel-usart.txt
+- ../spi/spi_atmel.txt
+- ../i2c/i2c-at91.txt
+
+Example:
+
+flexcom@f8034000 {
+	compatible = "atmel,sama5d2-flexcom";
+	reg = <0xf8034000 0x200>;
+	clocks = <&flx0_clk>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges = <0x0 0xf8034000 0x800>;
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+
+	spi@400 {
+		compatible = "atmel,at91rm9200-spi";
+		reg = <0x400 0x200>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_flx0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&flx0_clk>;
+		clock-names = "spi_clk";
+		atmel,fifo-size = <32>;
+
+		mtd_dataflash@0 {
+			compatible = "atmel,at25f512b";
+			reg = <0>;
+			spi-max-frequency = <20000000>;
+		};
+	};
+};

Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt

@@ -2,7 +2,11 @@ Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver
 
 Required properties:
  - compatible: value should be one of the following:
+   "atmel,at91sam9n12-hlcdc"
+   "atmel,at91sam9x5-hlcdc"
+   "atmel,sama5d2-hlcdc"
    "atmel,sama5d3-hlcdc"
+   "atmel,sama5d4-hlcdc"
  - reg: base address and size of the HLCDC device registers.
  - clock-names: the name of the 3 clocks requested by the HLCDC device.
    Should contain "periph_clk", "sys_clk" and "slow_clk".