usb: typec: tcpci: support edge irq

TCPCI USB PHY - PTN5110 could be used with SOCs that only support
the edge-triggered GPIO interrupts such as TI's K3 device AM69.
Move the interrupt configuration to the firmware which would
allow to accommodate edge triggered interrupts for such SOCs.
In order to support the edge interrupts, register irq line in advance
and keep track of occurrence during port registering.

When the edge interrupts are used, it is observed that some of the
interrupts are missed when tcpci_irq() is serving the current
interrupt. Therefore, check the status register at the end of
tcpci_irq() and re-run the function if the status is not clear
i.e. pending interrupt.

Signed-off-by: Emanuele Ghidoli <[email protected]>
Signed-off-by: Parth Pancholi <[email protected]>
Reviewed-by: Heikki Krogerus <[email protected]>
Reviewed-by: Francesco Dolcini <[email protected]>
Link: https://lore.kernel.org/r/[email protected]
Signed-off-by: Greg Kroah-Hartman <[email protected]>

drivers/usb/typec/tcpm/tcpci.c

@@ -707,10 +707,13 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 {
 	u16 status;
 	int ret;
+	int irq_ret;
 	unsigned int raw;
 
 	tcpci_read16(tcpci, TCPC_ALERT, &status);
+	irq_ret = status & tcpci->alert_mask;
 
+process_status:
 	/*
 	 * Clear alert status for everything except RX_STATUS, which shouldn't
 	 * be cleared until we have successfully retrieved message.
@@ -783,7 +786,12 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 	else if (status & TCPC_ALERT_TX_FAILED)
 		tcpm_pd_transmit_complete(tcpci->port, TCPC_TX_FAILED);
 
-	return IRQ_RETVAL(status & tcpci->alert_mask);
+	tcpci_read16(tcpci, TCPC_ALERT, &status);
+
+	if (status & tcpci->alert_mask)
+		goto process_status;
+
+	return IRQ_RETVAL(irq_ret);
 }
 EXPORT_SYMBOL_GPL(tcpci_irq);
 
@@ -915,20 +923,22 @@ static int tcpci_probe(struct i2c_client *client)
 
 	chip->data.set_orientation = err;
 
-	chip->tcpci = tcpci_register_port(&client->dev, &chip->data);
-	if (IS_ERR(chip->tcpci))
-		return PTR_ERR(chip->tcpci);
-
 	err = devm_request_threaded_irq(&client->dev, client->irq, NULL,
 					_tcpci_irq,
-					IRQF_SHARED | IRQF_ONESHOT | IRQF_TRIGGER_LOW,
+					IRQF_SHARED | IRQF_ONESHOT,
 					dev_name(&client->dev), chip);
-	if (err < 0) {
-		tcpci_unregister_port(chip->tcpci);
+	if (err < 0)
 		return err;
-	}
 
-	return 0;
+	/*
+	 * Disable irq while registering port. If irq is configured as an edge
+	 * irq this allow to keep track and process the irq as soon as it is enabled.
+	 */
+	disable_irq(client->irq);
+	chip->tcpci = tcpci_register_port(&client->dev, &chip->data);
+	enable_irq(client->irq);
+
+	return PTR_ERR_OR_ZERO(chip->tcpci);
 }
 
 static void tcpci_remove(struct i2c_client *client)