🌟 Support for TUF-AX3000 V2 🌟 #529

gnuton · 2024-01-22T00:44:08Z

gnuton · 2024-01-22T00:45:23Z

Looking for pre-alpha testers.
Pre-alpha builds may soft-brick your routers. So please be sure you know how to unbrick before applying as alpha tester.
If interested ping me.

Rovasteen · 2024-01-23T22:33:12Z

@gnuton I would like to test the TUF-AX3000 V2 firmware. Please let me know where to get the firmware.. Thank you!

gnuton · 2024-01-23T22:52:23Z

I will publish it here as soon as I do have a pre alpha

l0r3n75 · 2024-01-25T05:43:54Z

I'm willing to also test the pre alpha once you have it ready!

gnuton · 2024-01-31T17:29:22Z

I am gonna release the pre-alpha 1 volotunteer required..
ping me via discord.
NOTE: Pre-alpha can scft brick the device.. so please contact me only if you know how to recover.

Willemv2 · 2024-01-31T17:30:55Z

Can try it out for you i know how to recover, didn't got as far as you are now.

gnuton · 2024-01-31T19:32:23Z

pre alpha images:

[IMAGES REMOVED]

Note - you must be logged for downlaoding these images.
These are pre-alpha and they can soft brick your router. please do not flash them unless you know how to recover.

Rovasteen · 2024-01-31T20:57:42Z

Neither build worked for me. Flashed the default UI firmware and would not boot up even after setting the IP address manually. Flashed the 2nd build with TUF UI from recovery mode. Also did not work. So will go back into recovery mode and flash a stock image to start over again.

gnuton · 2024-02-01T00:28:24Z

@Rovasteen thanks for testing.

It seems like it's soldering time...
(picture from the internet... serial port seems to be on the right side)

Rovasteen · 2024-02-01T01:13:01Z

OK. I can get the recovery console up. Why can't I flash from there?

Rovasteen · 2024-02-01T04:15:35Z

I can easily get the router into recovery mode. The Asus firmware restoration tool stops at around 79% uploading. Flashing from the recovery console directly also does not seem to flash an image. Seems almost like there is an image size limit on the recovery console. I have never seem a Broadcom router that you could not recover from the recovery console until this one. Ideas?

Willemv2 · 2024-02-01T06:31:17Z

I can easily get the router into recovery mode. The Asus firmware restoration tool stops at around 79% uploading. Flashing from the recovery console directly also does not seem to flash an image. Seems almost like there is an image size limit on the recovery console. I have never seem a Broadcom router that you could not recover from the recovery console until this one. Ideas?

Did u try a lower version of the stock firmware ?

Rovasteen · 2024-02-01T18:35:53Z

I tried multiple FW versions including Asus initial image. I can get into recovery mode easily but none of the images flash. @gnuton what do you suggest as the router is NOT hard bricked yet I cannot load an image either.

gnuton · 2024-02-01T20:38:35Z

I soft bricked mine too. I have to check what to do. As suggested you should try to flash an old version of the stock firmware. Are you trying it through ftp or the Asus recovery tool? Just wondering if you are using the right procedure.

Willemv2 · 2024-02-01T20:40:21Z

I soft bricked mine too. I have to check what to do. As suggested you should try to flash an old version of the stock firmware. Are you trying it through ftp or the Asus recovery tool? Just wondering if you are using the right procedure.

Indeed first try the older firmware and try ftp side to see if it works or not before i brick mine too😅

Rovasteen · 2024-02-01T20:43:00Z

I held down power button and the reset button to get into recovery mode. I set the ethernet port to a fixed IP address as DHCP is not working of course on the router in this state. Tried flashing from Asus firmware recovery tool and also tried flashing directly from the recovery console using a browser. The firmware recovery tool gets to around 81% uploading the image before it fails.

Have not tried FTP. I just tried the old TFTP tool and it did not flash. What is the FTP procedure?

Rovasteen · 2024-02-01T21:34:38Z

I can ping the router all day long and I get back responses:

C:\Windows\System32>ping -t 192.168.1.1

Pinging 192.168.1.1 with 32 bytes of data:
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128
Reply from 192.168.1.1: bytes=32 time<1ms TTL=128

TFTP by command has not worked yet

C:\Windows\System32> tftp -i 192.168.1.1 put C:\TUF-AX3000_V2.pkgtb
Connect request failed

gnuton · 2024-02-01T21:46:43Z

This is the way I do use tftp on linux. If the mode is automatically set to binary than it should be fine.
I still need to test it on my TUF-AX3000 V2 and recoverit.. btw..

 # tftp
tftp> connect 192.168.1.1
tftp> mode binary
tftp> put THE_IMAGE

then wait until ou get that all data has been sent and wait a few minutes

If you attach a JTAG cable you should see some logs like these

enter tftp mode:
Reading ::
TFTP Server.
..tftp retry wait 0
Failed.: Timeout occured
Reading ::
TFTP Server.
..tftp retry wait 0
Failed.: Timeout occured
Reading ::
TFTP Server.
..tftp retry wait 0
Failed.: Timeout occured
Reading ::

gnuton · 2024-02-01T23:05:07Z

Tested and the good news I get same stuff as you @Rovasteen !
tftp> connect 192.168.1.1
tftp> mode binary
tftp> put TUF-AX3000_V2_3.0.0.4_388_23785-g6bb7c92_nand_squashfs.pkgtb
Transfer timed out.

gnuton · 2024-02-02T06:17:45Z

@Rovasteen It looks like HND devices are harder to recovery than older and you need to try many many times.
Sometimes yu have to find the right eth/wan port to get it working too. Typically, pinging to a device at CFE would return a TTL of 100 hops instead of 64 hops.

I have done just few tries, but I would next get a serial adapter for debuging and recover. Among the sevreal options the serial CP2102, seems to be the best.

Rovasteen · 2024-02-02T12:30:26Z

@gnuton could you contact Asus and get their recommendations as some of the new devices accept to boot from the serial port as an example. Maybe this device has some means of recovery that Asus can turn us onto.

Rovasteen · 2024-02-02T15:39:15Z

I can report my router is recovered. Here is what I did,, which I do not know if it is repeatable.

Connect Ethernet to Port 1 of the router, Set a fixed IP address at your computer as DHCP does not function in recovery mode.
Hold down WPS button for 15 seconds and turn on power to do a hard reset.
After hard reset, hold down reset button for 15 seconds and power on to put router in recovery mode.
Use browser and access the recovery console at 192.168.1.1 or whatever IP address you are using at your computer. Upload image from the recovery console. This may take a while.

I used the OEM image TUF-AX3000_V2_3.0.0.4_388_23785-g6bb7c92_nand_squashfs.pkgtb

Rovasteen · 2024-02-02T18:56:03Z

I don't know if this router has 2 partitions or not. It seems like holding down the WPS button during power on may have been what solved this.

gnuton · 2024-02-02T21:23:25Z

@Rovasteen yep I managed to recover mine too using the same method. I just pointed out the browser to the router IP and voila'.

gnuton · 2024-02-03T09:42:33Z

Build issues found:

sdparm

024-01-31T18:21:03.2144953Z make -C sdparm-1.02
2024-01-31T18:21:03.2225565Z make[5]: Entering directory '/project/asuswrt-merlin.ng/release/src/router/sdparm-1.02'
2024-01-31T18:21:03.2226580Z cd . && /bin/sh /project/asuswrt-merlin.ng/release/src/router/sdparm-1.02/missing --run aclocal-1.10 
2024-01-31T18:21:03.2294851Z /project/asuswrt-merlin.ng/release/src/router/sdparm-1.02/missing: line 52: aclocal-1.10: command not found
2024-01-31T18:21:03.2309572Z WARNING: `aclocal-1.10' is missing on your system.  You should only need it if
2024-01-31T18:21:03.2310824Z          you modified `acinclude.m4' or `configure.ac'.  You might want
2024-01-31T18:21:03.2311925Z          to install the `Automake' and `Perl' packages.  Grab them from
2024-01-31T18:21:03.2312729Z          any GNU archive site.
2024-01-31T18:21:03.2367578Z  cd . && /bin/sh /project/asuswrt-merlin.ng/release/src/router/sdparm-1.02/missing --run automake-1.10 --gnu 
2024-01-31T18:21:03.2411228Z /project/asuswrt-merlin.ng/release/src/router/sdparm-1.02/missing: line 52: automake-1.10: command not found
2024-01-31T18:21:03.2424682Z WARNING: `automake-1.10' is missing on your system.  You should only need it if
2024-01-31T18:21:03.2425547Z          you modified `Makefile.am', `acinclude.m4' or `configure.ac'.
2024-01-31T18:21:03.2426201Z          You might want to install the `Automake' and `Perl' packages.
2024-01-31T18:21:03.2426723Z          Grab them from any GNU archive site.
2024-01-31T18:21:03.2543636Z cd . && /bin/sh /project/asuswrt-merlin.ng/release/src/router/sdparm-1.02/missing --run autoconf
2024-01-31T18:21:03.3558579Z aclocal.m4:14: error: this file was generated for autoconf 2.61.
2024-01-31T18:21:03.3559621Z You have another version of autoconf.  If you want to use that,
2024-01-31T18:21:03.3560205Z you should regenerate the build system entirely.
2024-01-31T18:21:03.3560626Z aclocal.m4:14: the top level
2024-01-31T18:21:03.3564239Z autom4te: /usr/bin/m4 failed with exit status: 63
2024-01-31T18:21:03.3588974Z WARNING: `autoconf' is probably too old.  You should only need it if
2024-01-31T18:21:03.3590407Z          you modified `configure.ac'.  You might want to install the
2024-01-31T18:21:03.3591216Z          `Autoconf' and `GNU m4' packages.  Grab them from any GNU
2024-01-31T18:21:03.3591724Z          archive site.
```

2. sgdisk
```
2024-01-31T18:55:49.8876467Z /bin/sh: sgdisk: command not found
```
- FIXED

3. 
```
May  5 07:05:02 kernel: emf: Unknown symbol osl_malloc (err -2)
May  5 07:05:02 kernel: emf: Unknown symbol osl_pktdup_cpy (err -2)
May  5 07:05:02 kernel: emf: Unknown symbol osl_mfree (err -2)
May  5 07:05:02 kernel: emf: Unknown symbol linux_pktfree (err -2)
May  5 07:05:02 kernel: emf: Unknown symbol osl_pktdup (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_wmf_scbfind (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol osl_malloc (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_mfdb_ipv6_membership_add (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol osl_detach (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_rtport_del (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_igmp_snooper_register (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol osl_attach (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_mfdb_ipv6_membership_del (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_wmf_get_igsc (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_rtport_add (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_igmp_snooper_unregister (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_mfdb_membership_del (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol osl_mfree (err -2)
May  5 07:05:02 kernel: igs: Unknown symbol emfc_mfdb_membership_add (err -2)
```
Investigation
This may be an issue coming from upstream see https://www.linksysinfo.org/index.php?threads/tuf-ax3000-v2-installation.78070/page-2
```
###
it looks like emfc_mfdb_ipv6_membership_add is defined in the emf.o object file and is referenced in the igs.o object file.

$ nm -an asuswrt/release/src-rt-5.04axhnd.675x/router-sysdep/hnd_extra/prebuilt/igs.o | grep emfc_mfdb_ipv6_membership_add
         U emfc_mfdb_ipv6_membership_add   

$ nm -an asuswrt/release/src-rt-5.04axhnd.675x/router-sysdep/hnd_extra/prebuilt/emf.o | grep emfc_mfdb_ipv6_membership_add
00000000 r ___ksymtab+emfc_mfdb_ipv6_membership_add
00000000 r __ksymtab_emfc_mfdb_ipv6_membership_add
0000004c r __kstrtab_emfc_mfdb_ipv6_membership_add
00002324 T emfc_mfdb_ipv6_membership_add

```

4. The boot gets stuck in this loop
```
May  5 07:05:39 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:06:10 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:06:10 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:06:13 Mastiff: exit.
May  5 07:06:41 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:06:41 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:07:12 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:07:12 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:07:43 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:07:43 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:08:14 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:08:14 rc_service: watchdog 2531:notify_rc start_cfgsync
May  5 07:08:45 rc_service: watchdog 2531:notify_rc start_amas_lanctrl
May  5 07:08:45 rc_service: watchdog 2531:notify_rc start_cfgsync
```


5. maybe not an issue
```
ay  5 07:05:10 lldpd[2597]: could not open either /etc/os-release or /usr/lib/os-release
May  5 07:05:10 lldpd[2597]: lsb_release information not available
May  5 07:05:10 lldpd[2601]: created chroot directory /var/run/lldpd
May  5 07:05:10 lldpd[2601]: /etc/localtime copied to chroot
May  5 07:05:10 lldpd[2601]: protocol LLDP enabled
May  5 07:05:10 lldpd[2601]: protocol CDPv1 disabled
May  5 07:05:10 lldpd[2601]: protocol CDPv2 disabled
May  5 07:05:10 lldpd[2601]: protocol SONMP disabled
May  5 07:05:10 lldpd[2601]: protocol EDP disabled
May  5 07:05:10 lldpd[2601]: protocol FDP disabled
May  5 07:05:10 lldpd[2601]: libevent 2.0.21-stable initialized with epoll method
May  5 07:05:10 lldpcli[2598]: lldpd should resume operations
```

Rovasteen · 2024-02-03T14:56:29Z

Awesome progress @gnuton ! Looking forward to the first bootable build. Hopefully, Asus is also providing latest Broadcom drivers (at least I can hope for that). Take care and thank you for supporting this router!

Rovasteen · 2024-02-09T12:08:06Z

@gnuton you've done a really professional job setting up your github. Everything is extremely well organized and well labeled. It's been interesting looking at Actions to see how the test builds are coming along. Many thanks to you!

gnuton · 2024-03-30T17:14:57Z

The firmware has been merged to the main branch and now all images get released along with the other ones.

DTHPM · 2024-03-30T23:58:12Z

Error IPTV (beta 1)

gnuton · 2024-04-02T05:29:19Z

@DTHPM ?

DTHPM · 2024-04-03T23:25:05Z

Black error on channels when using iptv (Ax3000v2- beta1)

DavidGaribov · 2024-04-04T18:29:50Z

@gnuton Hello. Have you tried changing the router firmware region? I need to know what is responsible for the regional settings nvram or cfe.bin? I tried to change the firmware region: I managed to get the cfe.bin file, but when I tried to edit it, the cfe editor received the wrong cfe error. It is very likely that all parameters are stored in nvram, I managed to get a list of nvram parameters responsible for the firmware region and change them, but unfortunately the changes were not saved. The ability to change the region is necessary to obtain maximum amplification of the wifi signal.

Hakwish · 2024-04-05T02:43:49Z

@gnuton hi, i apreciate the great work you are doing, but will you concider updating the the gaming priority in adaptive Qos section so it will recognize modern games ? cuz in the stock version it does not work at all, thanks

gnuton · 2024-04-05T03:21:50Z

If broken in the stock firmware, than it s not an easy fix and this may affect also other routers. I am not sure what s broken since this is the first time I hear this. I would suggest you to open a dedicated ticket and talk on the forum about this with others. Then you may come with a more clear understanding of the problem and we can check what can be done. You can also contact Asus to fix this if in stock

SMOL25 · 2024-04-05T12:17:57Z

[

What file should i download?

gquittet · 2024-04-05T22:08:47Z

@SMOL25

[

What file should i download?

Just download this one https://github.com/gnuton/asuswrt-merlin.ng/releases/download/3004.388.6_2-gnuton1/TUF-AX3000_V2_3004_388.6_2-gnuton1_tuf_nand_squashfs.pkgtb and check the md5sum of this file using https://github.com/gnuton/asuswrt-merlin.ng/releases/download/3004.388.6_2-gnuton1/TUF-AX3000_V2_3004_388.6_2-gnuton1_tuf_nand_squashfs.pkgtb.md5

Shasoosh · 2024-04-07T15:54:06Z

What's the difference between these two?

TUF-AX3000_V2_3004_388.6_2-gnuton1_nand_squashfs.pkgtb
TUF-AX3000_V2_3004_388.6_2-gnuton1_tuf_nand_squashfs.pkgtb

sojusnik · 2024-04-07T20:02:49Z

TUF-AX3000_V2_3004_388.6_2-gnuton1_nand_squashfs.pkgtb = default ASUS routers skin
TUF-AX3000_V2_3004_388.6_2-gnuton1_tuf_nand_squashfs.pkgtb = gamer-like skin of ASUS routers (which is the default skin for this stock firmware, which IMHO looks horrible, so gnuton kindly provided the default ASUS skin)

Shasoosh · 2024-04-07T20:53:19Z

Thanks for clarifying.

kokosowy · 2024-04-18T15:45:00Z

Hi! Many thanks for releasing it. I've just installed and configured it. I have a question. Neither stock firmware neither FreshTomato nor Gnuton's Merlin do not support VLANs at the moment. Is this limitation coming from stock firmware delivered by Asus or this is more complicated?

mustymute · 2024-05-28T15:06:57Z

hello guys where stable version download link ? thanks.

gquittet · 2024-05-28T15:36:07Z

hello guys where stable version download link ? thanks.

@mustymute Here: https://github.com/gnuton/asuswrt-merlin.ng/releases/tag/3004.388.6_2-gnuton1

And download the TUF-AX3000_V2_3004_388.6_2-gnuton1_tuf_nand_squashfs.pkgtb file.

lenovomen · 2024-08-27T15:13:55Z

How can I update the bootloader part of my router? Or reinstall the whole router to make sure it is free of any spyware or viruses? Anyone got any ideas?

Wismycorp · 2024-08-31T20:13:13Z

Looking for pre-alpha testers. Pre-alpha builds may soft-brick your routers. So please be sure you know how to unbrick before applying as alpha tester. If interested ping me.

Hello, I have 2 ax3000v2, if you need any help with alpha and beta testing, you can count on me. Do whatever I can

sojusnik · 2024-08-31T21:04:39Z

Hello, I have 2 ax3000v2, if you need any help with alpha and beta testing, you can count on me. Do whatever I can

Stable release is already out there: https://github.com/gnuton/asuswrt-merlin.ng/releases/tag/3004.388.8_2-gnuton1

Wismycorp · 2024-08-31T22:47:14Z

Hello, I have 2 ax3000v2, if you need any help with alpha and beta testing, you can count on me. Do whatever I can

Stable release is already out there: https://github.com/gnuton/asuswrt-merlin.ng/releases/tag/3004.388.8_2-gnuton1

Thank you, but if you need anything, please contact us. The more I’m sure that this is not the last version of the build

sojusnik · 2024-09-01T06:41:57Z

Thank you, but if you need anything, please contact us. The more I’m sure that this is not the last version of the build

Well, you could check if you can reproduce this bug: #664 (there seems to be an issue when upgrading from stock to this firmware)

Stinkergood · 2024-09-01T16:37:37Z

What feature implemented that firmware mod?

sveto8 · 2024-09-06T12:12:22Z

Hi all!

Can I restore settings from stock firmware after updating this FW?
(TUF-AX3000 V2)

Tnx!

Regards
Sveto

gnuton · 2024-09-06T12:22:07Z

Hi all!

Can I restore settings from stock firmware after updating this FW? (TUF-AX3000 V2)

Tnx!

Regards Sveto

No.

sveto8 · 2024-09-08T08:09:31Z

Hi all!
Can I restore settings from stock firmware after updating this FW? (TUF-AX3000 V2)
Tnx!
Regards Sveto

No.

Thanks for the info.

I have updated FW to TUF-AX3000_V2_3004_388.6_2-gnuton1_nand_squashfs.pkgtb from stock FW and the settings remained on the router, I didn't lose them. I only had to enable the VPN server again (OpenVPN).

Njara2424 · 2024-10-22T10:08:57Z

Hello all,

I had just received my first ASUS Tuf Gaming ax3000 V2 router
and there's no VPN client option in it, only VPN client is mentioned.
is there a solution to make it appear?

thanks

kokosowy · 2024-10-22T11:55:33Z

Hi @Njara2424. There are both, VPN client and VPN server:

Njara2424 · 2024-10-22T13:39:17Z

On my interface.
There are no other options
Only VPN server appears

Do I need to update?

kokosowy · 2024-10-22T13:44:00Z

I think it's just different visually, all functions should be the same. Just make sure you installed gnuton's firmware successfully.

I'm currently using this version, without TUF GUI - https://github.com/gnuton/asuswrt-merlin.ng/releases/download/3004.388.8_2-gnuton1/TUF-AX3000_V2_3004_388.8_2-gnuton1_nand_squashfs.pkgtb

Njara2424 · 2024-10-23T04:06:28Z

thanks a lot bro

gnuton added the bug Something isn't working label Jan 22, 2024

gnuton mentioned this issue Jan 22, 2024

🔥 New Models to support for 2024 🔥 #523

Open

gnuton self-assigned this Jan 23, 2024

gnuton closed this as completed Apr 6, 2024

🌟 Support for TUF-AX3000 V2 🌟 #529

🌟 Support for TUF-AX3000 V2 🌟 #529

Comments

gnuton commented Jan 22, 2024 • edited Loading

gnuton commented Jan 22, 2024 • edited Loading

Rovasteen commented Jan 23, 2024

gnuton commented Jan 23, 2024 • edited Loading

l0r3n75 commented Jan 25, 2024

gnuton commented Jan 31, 2024

Willemv2 commented Jan 31, 2024

gnuton commented Jan 31, 2024 • edited Loading

Rovasteen commented Jan 31, 2024

gnuton commented Feb 1, 2024 • edited Loading

Rovasteen commented Feb 1, 2024

Rovasteen commented Feb 1, 2024

Willemv2 commented Feb 1, 2024

Rovasteen commented Feb 1, 2024

gnuton commented Feb 1, 2024 • edited Loading

Willemv2 commented Feb 1, 2024

Rovasteen commented Feb 1, 2024 • edited Loading

Rovasteen commented Feb 1, 2024

gnuton commented Feb 1, 2024 • edited Loading

gnuton commented Feb 1, 2024

gnuton commented Feb 2, 2024

Rovasteen commented Feb 2, 2024

Rovasteen commented Feb 2, 2024

Rovasteen commented Feb 2, 2024

gnuton commented Feb 2, 2024 • edited Loading

gnuton commented Feb 3, 2024 • edited Loading

Rovasteen commented Feb 3, 2024

Rovasteen commented Feb 9, 2024

gnuton commented Mar 30, 2024

DTHPM commented Mar 30, 2024

gnuton commented Apr 2, 2024

DTHPM commented Apr 3, 2024

DavidGaribov commented Apr 4, 2024

Hakwish commented Apr 5, 2024

gnuton commented Apr 5, 2024 • edited Loading

SMOL25 commented Apr 5, 2024

gquittet commented Apr 5, 2024 • edited Loading

Shasoosh commented Apr 7, 2024

sojusnik commented Apr 7, 2024

Shasoosh commented Apr 7, 2024

kokosowy commented Apr 18, 2024 • edited Loading

mustymute commented May 28, 2024 • edited Loading

gquittet commented May 28, 2024 • edited Loading

lenovomen commented Aug 27, 2024

Wismycorp commented Aug 31, 2024

sojusnik commented Aug 31, 2024

Wismycorp commented Aug 31, 2024

sojusnik commented Sep 1, 2024

Stinkergood commented Sep 1, 2024

sveto8 commented Sep 6, 2024

gnuton commented Sep 6, 2024

sveto8 commented Sep 8, 2024

Njara2424 commented Oct 22, 2024

kokosowy commented Oct 22, 2024 • edited Loading

Njara2424 commented Oct 22, 2024

kokosowy commented Oct 22, 2024

Njara2424 commented Oct 23, 2024

gnuton commented Jan 22, 2024 •

edited

Loading

gnuton commented Jan 22, 2024 •

edited

Loading

gnuton commented Jan 23, 2024 •

edited

Loading

gnuton commented Jan 31, 2024 •

edited

Loading

gnuton commented Feb 1, 2024 •

edited

Loading

gnuton commented Feb 1, 2024 •

edited

Loading

Rovasteen commented Feb 1, 2024 •

edited

Loading

gnuton commented Feb 1, 2024 •

edited

Loading

gnuton commented Feb 2, 2024 •

edited

Loading

gnuton commented Feb 3, 2024 •

edited

Loading

gnuton commented Apr 5, 2024 •

edited

Loading

gquittet commented Apr 5, 2024 •

edited

Loading

kokosowy commented Apr 18, 2024 •

edited

Loading

mustymute commented May 28, 2024 •

edited

Loading

gquittet commented May 28, 2024 •

edited

Loading

kokosowy commented Oct 22, 2024 •

edited

Loading